How To Measure Countertops For Granite

Some countertops are as easy to divide into rectangles, as we saw in the kitchen above. Area = length × width.

custom and granite counter tops Custom

To calculate the area of the oddly shaped piece below, we will follow the same formula:

How to measure countertops for granite. 54 x 30 = 1620 sq. Follow these steps to measure for countertops. It may look like it would be simple, but there are many variables to determine this including possible waste factor.

108” x 25.5” = 2,754 (divide this number by 144) 2,754/144 = 19.12 sq ft. 31 in x 25.5 in = 790.5 sq in. You just take the length x width of each section, and add it together.

If you would like get accurate estimate for your granite countertops. Please note that granite countertops have a 1 ½” standard over hang from the face of the cabinets. 15.0 + 11.25 = 26.25 sq.

Don’t stop measuring when you reach a sink but continue to measure until you reach the end of a cabinet, appliance, or a wall. Sketch your countertop layout, noting the approximate location of the sink, cooktop, and other cutouts. 125” x 25” = 3125”.

Measure the length of one section of your countertops by running a measuring tape flush along the back edge of the section from one end to the other end. Measure depth, from wall or back of counter to front for each section as well. Just measure the length starting from the flat end to the farthest point on the curve or the apex.

The length of your 1st existing countertop is 125” and width is 25” or 125” x 25”. An island countertop that is not against the wall will require a 1¼” overhang on each side or, if. Same size as a in this case, so 1562.5”.

For example, say the length of the countertop is 108” and the depth of the standard countertop (on a 24” deep cabinet) is 25 ½”; So, 44 inches times 26 inches yields 3,744 square inches. Divide your countertop into sections (refer to the above chart for some typical layouts) measure the length and width of each section (in inches) of your countertop.

62.5” x 25” = 1562.5”. Using the box method, start at the wall and measure to the counter edge. Divide the figure you get by performing the steps above by 144.

Make sure you measure to the closest 1/8 inch. Your fabricator will ask for the measurements of your counters. Clear your countertops of any appliances, vases or other items.

Multiply your total length by 26, the width in inches of standard countertops, to find total countertop area in square inches. / the total counter top is 26 ¼ sq. This will help determine how many slabs we will need for your project.

For galley kitchens or in island situations, don’t be concerned about scaling the aisle separations. Measure length from end of counter to wall or point where next section of countertop begins. Note that the average measurement of the backsplash is 4 inches.

Take the length of section b & multiply by the depth of section b. Add the total of section a & section b & round to the nearest ¼ sq. If they prefer square feet, just divide that number by 12.

Measure the length in the same manner. Below are step by step instructions on how to measure your existing countertops. Standard height of splash = 4 inches.

Multiply the length of your of your granite countertops by 4. 31 in x 4 in = 124 sq in. Countertops prior to meeting with a granite surfaces sales associate.

However, handy homeowners can save money by measuring and installing the countertops themselves. This can help you get the right granite figure the backsplash needs. You can use the graph paper on the back of this page to draw your kitchen countertop configuration and record your measurements.

Each sq foot has 144 sq in. Choosing granite as the surface for your countertops is an investment. Once completed, you can tear out the sheet along the perforated.

However, the calculations for the area are the same. You will need to reach the wall behind the countertop and use a tape measure, so make sure nothing. Your regular standard kitchen base cabinet is 24″ deep.

This will give you the width. Divide this number by 144. 1620 ¸ 144 = 11.25 sq.

914.5 sq in / 144 sq in = 6.35 sq ft. Use the tape measure to measure each section of countertop in inches. Take measurements of the entire length of each countertop you want covered in granite.

* now divide by 144 to obtain square footage. Always start from the wall and measure to the edge of your countertop. Make sure to measure each counter section individually and as accurately as possible.

Square inches of bar area. Multiply this number by the width then divide by 144 to get the total square footage estimate. Important considerations when measuring for granite countertops.

Begin with a scale drawing of your countertop layout or layouts. How to measure for appliances It’s important to figure out square footage.

47 Drop Dead Granite Counters Kitchen